Integrated passive devices such as resistors, capacitors, coils and transformers have been introduced by several companies^[1]. Extended failure analysis revealed that electrostatic discharge (ESD) and electrical overstress (EOS) are the reason for approximately half of all circuit failures for integrated devices. Thus, excellent ESD protection is becoming more important. High ESD robustness of the circuits guarantees high yield in production, and additionally reduces the field failure rate of applications^[3]. The most popular ESD models are the human body model (HBM), the machine model (MM), and the charged device model (CDM). The last one is of growing interest because it is a special kind of electronic discharge, showing good agreement with present ESD failure mechanisms in chip manufacturing. Each model describes a special kind of ESD discharge and is further classified into different ESD classes.

In order to protect integrated filter circuits from ESD, ESD devices are either placed as discrete circuits around the critical input/output pins or integrated with the filter onto the chip. The last concept leads to a cheaper and smaller PCB outline^[4].

For the development of RF filters, a compromise between RF performance and ESD protection must be found. The non-linearities of active ESD devices, for example, can cause intermodulation and degrade the RF performance.

The new RF bandpass filter with integrated impedance matching, mode conversion and ESD protection is manufactured with an extended silicon-copper technology that allows integration of active and passive components on a single die. In the following sections, an RF filter with excellent ESD protection and filter performance will be discussed, and an analytical HBM simulation setup for these filters will be introduced.

An existing silicon-copper technology for passive integration was extended in order to integrate passive and active elements on a high-resistive Si substrate. Figure 1 shows the cross-section of the layer sequence for a typical RF filter with monolithic integrated planar inductors, metal-insulator-metal (MIM) capacitors, and ESD diodes.

Coils and transformers are implemented in three-layer copper metallization. Metal-1 has a thickness of 600 nm and is mainly applied to lead through the metallization from the inside to the outside of the coils. Metal-2 and metal-3 have thicknesses of 2500 nm and are used for adjusting the coils to the required inductance. Due to the performance limitation of the skin effect, these stacked coils can be used for RF applications above 1 GHz. For lower-frequency applications, an increase of the copper layer thickness would be necessary to improve the quality factor (Q) of the inductors substantially. The inductances of typical integrated coils are in the range of 0.5 nH to 35 nH, with corresponding Q factors between 10 GHz and 16 at 1 GHz. Maximum Q values of about 40 were measured at 3 GHz for a corresponding L value of 0.5 nH.

The Al₂O₃ MIM capacitors, which are necessary for the implementation of on-chip resonators, are placed between metal-1 and metal-2. With the new dielectric material, high specific capacitance values of from 1.4 fF/µm² to 1.8 fF/µm² can be achieved leading to small capacitor dimensions and small outlines of the chip design. The values for the MIM capacitors are in the range of between 0.1 pF and 30 pF, with corresponding Q factors of 100 at 1 GHz.

With the extended S technology, filters with low insertion loss and high harmonic suppression can be designed. An integration of filter elements and balun on-chip replaces a high number of external SMD components, leading to reduced board space and lower assembly costs. Further advantages compared to discrete solutions are smaller component tolerances of these integrated devices and a reduced assembly error rate.

The schematic of the implemented PCN/PCS bandpass filter (1710 MHz to 1910 MHz) with mode conversion from differential to single ended is shown in Figure 2. The filter consists of a symmetrical filter design based on several optimized LC resonators. The mode conversion is carried out with an integrated autotransformer with a coupling factor of 0.83.

We focused on a high common-mode suppression at the second harmonic, leading to a symmetrical filter design. This design reduces the influence of the grounding to the common-mode signal, which results in an excellent common-mode suppression of about -40 dB at the second harmonic. In addition, the symmetrical design allows implementation of a dc biasing network in the mirror plane of the filter, acting as a dc current supply typically used to drive the modulators of a transceiver. The bandpass filter itself is housed in a thin, small, and leadless package with dimensions of only 2.0 × 1.3 × 0.4 mm^[3].

Coils and autotransformers were considered in the simulation tool by de-embedded S-parameter measurements and a Spice netlist generated by a simulation tool, respectively. The parameters of the autotransformer model are extracted from its geometrical structure by applying a numerical solver for the electric and magnetic fields.

Figure 3 and Figure 4 show the insertion loss versus frequency and the common-mode suppression of a harmonic PCN/PCS filter, respectively. The insertion loss within the passband (1710 MHz and 1910 MHz) is about -2.5 dB, with a corresponding ripple of only 0.2 dB.

The suppression of the third harmonic is below -40 dB and in good agreement with the simulation results.

Using an autotransformer instead of a simple LC balun leads to an improved common-mode suppression of -30 dB in the frequency range between 3 GHz and 6 GHz. However, the simulation and measurement results differ at higher frequencies because of the implemented autotransformer model, which is only valid up to half of the self-resonance of the autotransformer itself.

1 2 Next

RSS    Save to Del.icio.us  Digg This